NTLDR is missing. Updated: 0. 5/0. 5/2. Computer Hope. Below are the full error messages that may be seen when the computer is booting. This is usually due to an error in the boot.ini file. The entry for NT is either missing or incorrect. Edit the boot.ini file and check the entry for NT. Information: System Requirements: Runs on Microsoft Windows 7, Windows Vista, Windows XP and 2000. Including 32-bit & 64-bit versions. Download size: 3.4 MB. NTLDR is missing. Press CTRL+ALT+DEL to restart Written on February 15th 2010 at 08:02. Last modified: October 16, 2011. NTLDR is Missing. Press any key to restart. Boot: Couldn't find NTLDRPlease insert another disk. NTLDR is missing. Press Ctrl Alt Del to Restart. Computer is booting from a non- bootable source. Vista Hal.dll Missing Or Corrupt Win
Many times this error is caused when the computer is attempting to boot from a non- bootable floppy disk or CD- ROM. First verify that no floppy diskette or CD is in the computer, unless you are attempting to boot from a diskette. Note: This error has also been known to occur when a memory card is in a card reader and the computer is attempting to boot from it. If you have any card reader or flash reader, make sure that no memory stick is inside the reader. Additionally, disconnect all USB drives, cameras, ipods, iphones, etc. ![]() For example, if you are attempting to run the install from the CD- ROM, make sure the CD- ROM is the first device listed in the boot sequence, instead of the hard drive. Also, when the computer is booting, you should receive the below prompt: Press any key to boot from the CDImportant: When you see this prompt, press any key on the keyboard immediately, such as the Enter or Space key. Otherwise, the computer will try booting from the hard drive and likely get the NTLDR error again. Note: If you are not receiving the above message and your BIOS boot options are set properly, it's also possible that your CD- ROM drive may not be booting from the CD properly. Verify the jumpers are set properly on the CD- ROM drive. Computer hard drive is not properly setup in CMOSVerify that your computer hard drive is properly set up in the CMOS setup. Improper settings can cause this error. Corrupt NTLDR or NTDETECT. COM file. Windows 2. Vista Hal.dll Missing Or Corrupt DllWindows XP users. Windows 2. 00. 0 users. If your computer is using Microsoft Windows 2. ![]() NTLDR error, create the below boot. Both of these files are located in the root directory of the primary hard drive. For example, C: \NTLDR and C: \NTDETECT. COM should be the locations of these files on many computers. Once these files have been copied to a floppy diskette, reboot the computer and copy the NTLDR and NTDETECT. COM files to the root directory of the primary hard drive. Below is an example of the commands that should be performed from the A: \> floppy drive to copy the files. ![]() After the above two files have been copied, remove the floppy diskette and reboot the computer. Windows XP users. Insert the Windows XP bootable CD into the computer. When prompted to press any key to boot from the CD, press any key on the keyboard. Once in the Windows XP setup menu, press the . Enter that password. Copy the below two files to the root directory of the primary hard drive. In the example below, we are copying these files from the CD- ROM drive letter, which in this case is . If so, try the below recommendations. Boot the computer with a Windows 9. Windows 9. 8 or Windows ME bootable diskette. At the A: \> prompt, type sys c: and press Enter. After pressing Enter, you should receive the . Once this has been completed, remove the floppy diskette and reboot the computer. New hard drive being added. If you are attempting to add a new hard drive to the computer, make sure the drive is a blank drive. Adding a new hard drive to a computer that already has Windows installed on it may cause the NTLDR error to occur. If you are unsure if the new drive is blank, try booting from a bootable diskette and format the new hard drive. Corrupt boot sector or master boot record. It's possible your computer's hard drive may have a corrupt boot sector or master boot record. These can be repaired through the Microsoft Windows Recovery console by running the fixboot and fixmbr commands. Seriously corrupted version of Windows 2. Windows XPIf you have tried each of the above recommendations that apply to your situation and you continue to receive the NTLDR error, there may be a more serious corruption issue in Microsoft Windows. Therefore, we would recommend reinstalling Microsoft Windows. If you are encountering this issue during your setup, you may want to completely erase your computer hard drive and all of its existing data and re- install Microsoft Windows. Loose or Faulty IDE/EIDE hard drive cable. This issue has been known to be caused by a loose or defective IDE/EIDE cable. If your hard drive uses an IDE or EIDE interface, check that the computer hard drive cable is firmly connected. Disconnect and then reconnect the cable, making sure that the connection is snug and secure. If the issue continues, it is also a possibility that the computer has a faulty cable, try replacing the hard drive cable with another cable or a new cable. Bad hard drive. If none of the above suggestions work to resolve the issue, there is a strong possibility the hard drive is bad and needs to be replaced. You can try installing a new hard drive and installing Windows on that hard drive to see if that resolves the issue. Additional information. See the NTLDR definition for further information and related links.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
August 2017
Categories |